shopping cart empty
michaeldoc69's Product Reviews
Sort:

Avatar
michaeldoc69
Member

VERIFIED OWNER
  • JoinedDec 2013
  • Posts 742
  • Reviews 109
  • Kudos1652
Overall   (3.0)
› Quality
› Value
4 of 5 people found the following review helpful
Pros: 1. Vapes good. Wicks well. Doesn’t leak. Airflow is a bit tight. Not adjustable, but could be drilled out. 2. Nice Drip Tip with dual O-Rings. Cons: 1. It barley holds 10 ML of Juice instead of 20 ML advertised. 2. Positive Post screw Washer shorts to Negative. Don’t use it. 3. When the Side Airflow hole was drilled, the burr was not removed and it shorts to Center Pin. Remove burr. 4. The chimney bottom portion is cracked. 5. The chimney is wider but shallower, if the post screws are not all the way in, the top portion of the chimney will touch the screws, creating a short circuit. It is kind of like Fogger V4+. Its Juice capacity is falsely advertised (Doubled). The quality of the workmanship is very poor, but if coiled and wicked right – it vapes like a champ. I built it with 0.8 Ohm coil of 0.8mm Flat Ribbon and wicked with Rayon (like cotton), both ends of the wick are just resting on the deck. Like Kayfun normal build. [IMG]http://i.imgur.com/32RUppf.jpg[/IMG]
Reviewed on Was this review helpful to you? Yes / No

Avatar
michaeldoc69
Member

VERIFIED OWNER
  • JoinedDec 2013
  • Posts 742
  • Reviews 109
  • Kudos1652
Overall   (2.0)
› Quality
› Value
2 of 2 people found the following review helpful
PROS
Good looking
CONS
Buns cotton at 400°F Shows resistance lower by 0.04Ω than it actually is.
Mine came with it's copper Positive 510 screw jammed in it. No way to turn it in either direction. I actually had to drill and re-thread it to make it work. But that's not all. It detects every nickel built atomizer lower by 0.04Ω than it actually is. And most important: It burns dry cotton when temperature limit is set for 400°F. That is absolutely NOT acceptable. Neither Evolv DNA40, or Yihi SX350 would do that.
Reviewed on Was this review helpful to you? Yes / No
6 Pieces Steel Rotary Milling Cutter Grinding Head
6 Pieces Steel Rotary Milling Cutter Grinding Head

Avatar
michaeldoc69
Member

VERIFIED OWNER
  • JoinedDec 2013
  • Posts 742
  • Reviews 109
  • Kudos1652
Overall   (4.7)
› Quality
› Value
2 of 2 people found the following review helpful
This is NON the best Stainless Steel cutting tool, but it cuts Brass, Copper, Aluminum - no problems.
Reviewed on Was this review helpful to you? Yes / No

Avatar
michaeldoc69
Member

VERIFIED OWNER
  • JoinedDec 2013
  • Posts 742
  • Reviews 109
  • Kudos1652
Overall   (5.0)
› Quality
› Value
2 of 2 people found the following review helpful
PROS
Very well machined and finished True 20 ML capacity Adjustable Airflow Clear tank section included
CONS
None
I've got 30mm version 10ml and 28.5mm ToBeCo 15ml one. They work fine. But this Huge Kayfun Lite Plus is the ultimate version. It has a regular Kayfun size Deck and Chimney and works just like any Kayfun does, but it actually, truly holds 20 ML of liquid! Thank you Fast Tech!
Reviewed on Was this review helpful to you? Yes / No

Avatar
michaeldoc69
Member

VERIFIED OWNER
  • JoinedDec 2013
  • Posts 742
  • Reviews 109
  • Kudos1652
Overall   (5.0)
› Quality
› Value
2 of 2 people found the following review helpful
I modified mine by installing a brass disk under the delrine cap, just like the earlier clones and the original were. It fires every time now.
Reviewed on Was this review helpful to you? Yes / No