shopping cart empty
esc1218's Product Reviews
Sort:
*SALE* Replacement POM Heat Insulation Gasket for Atomizers (10-Pack)
*SALE* Replacement POM Heat Insulation Gasket for Atomizers (10-Pack)

esc1218
Member

VERIFIED OWNER
  • JoinedSep 2014
  • Posts 5
  • Reviews 134
  • Kudos2
Overall   (5.0)
› Quality
› Value
6 of 6 people found the following review helpful
I have found these to be useful tools and should be in every vapers arsenal, if they lower the price. I can confirm 3 functions of these washers; scratch protection, heat protection, and gap filling. Most obvious and the main reason I purchased them is for scratch protection for expensive regulated mods. Heat protection needs to be more clearly defined, as they do a poor job of actually dispersing heat, they really just slow heat transfer down a bit. Chain vaping at 100w or higher these are pretty much useless. A 510 heat sinc connector would be a wiser choice for heat dissipation. And finally, gap filling. You know those really long 510 connectors, like the notorious magma, that can make your mech mod button stick out or put excess stress on a spring loaded 510 connector? Slap one of these between the 2 and problem sloved.
Reviewed on Was this review helpful to you? Yes / No
*SALE8 3-Piece Anodized Aluminum Tubes for Nemesis
*SALE8 3-Piece Anodized Aluminum Tubes for Nemesis

esc1218
Member

VERIFIED OWNER
  • JoinedSep 2014
  • Posts 5
  • Reviews 134
  • Kudos2
Overall   (5.0)
› Quality
› Value
2 of 2 people found the following review helpful
These tubes are absolutely wonderfull. They are softer than stainless and therefore easier to damage, but they reduce the weight of your setup, especially when paired with a PC or PMMA tank on a kayfun lite. I have not tested, but being made of aluminum, they should also conduct electricity better, even with the anodize. Speaking of which, the tubes are beautifully anodized inside and out, with the exception of the threads for the top cap and switch. The lockring threads do not affect function at all on the set I received. In fact, they are more smooth than the threads on my stainless nemesis clone. If you want to use a kick, due to the anodizing on the inside, you first need to sand or file where your kick's negative post will come into contact with the sidewall of the tube. I used a sand paper tube attachment for a dremel, but on a drill, and it worked perfectly. Took 2 minutes of sanding and now i can use a kick in either the 18650 or the 18500 tube.
Reviewed on Was this review helpful to you? Yes / No
UltraFire Nylon Black Flashlight Holster (Mid-size)
UltraFire Nylon Black Flashlight Holster (Mid-size)

esc1218
Member

VERIFIED OWNER
  • JoinedSep 2014
  • Posts 5
  • Reviews 134
  • Kudos2
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
Perfect for most average size 18650 mods/flashlights. I can confirm it will fit 18650 SMPL, nemesis, stingray, and 4 nine with a tank as tall as a kayfun 3.1 standard, or a kanger subtank, or any dripper I own. A bit too tall for an 18650 mod with an average dripper. There is a shorter holster on fasttech that has a battery pouch on the side that is perfect for shorter set ups. This is the 3rd one I have purchased, the other 2 are a few months old and still holding up fine.
Reviewed on Was this review helpful to you? Yes / No
Authentic infinite CLT RDA Rebuildable Drpping Atomizer
Authentic infinite CLT RDA Rebuildable Drpping Atomizer

esc1218
Member

VERIFIED OWNER
  • JoinedSep 2014
  • Posts 5
  • Reviews 134
  • Kudos2
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
One of my favorite rda's. Lots of airflow if you attach a TOBH chuff cap. Yes, they do fit. You may have to try different o rings but the 2 TOBH one piece chuff caps I tried fit as is. Shallow juice lip ( or juice well ) but lots of airspace above where your coils set so its great for clouds, if you have a chuff attached. With the provided top cap and drip tip, its a pretty tight draw for big lung hits. Great machining, no excess metal or burrs or sharp edges. Very pleased with this rda. I feel that its worth the extra money to have the factory do the finishing work for me, as I found nothing on this rda that needed extra work. Most of your $10 rda's need some finishing work.
Reviewed on Was this review helpful to you? Yes / No
Replacement Bottom Cap for Nemesis Mechanical Mods
Replacement Bottom Cap for Nemesis Mechanical Mods

esc1218
Member

VERIFIED OWNER
  • JoinedSep 2014
  • Posts 5
  • Reviews 134
  • Kudos2
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
Threads are fine. Replace spring with magnets also sold here. Lacks the vents that are supposed to be present in nemesis switches but I don't mind it as I am extremely careful with my builds and set ups. Something to be aware of though.
Reviewed on Was this review helpful to you? Yes / No