shopping cart empty
cycoblazer's Product Reviews
Sort:
SJMY Replacement 316 Stainless Steel Tank for Fire Bird RTA Atomizer
SJMY Replacement 316 Stainless Steel Tank for Fire Bird RTA Atomizer

Avatar
cycoblazer
Member

VERIFIED OWNER
  • JoinedJul 2016
  • Posts 108
  • Reviews 172
  • Kudos83
Overall   (5.0)
› Quality
› Value
3 of 3 people found the following review helpful
I received this yesterday. It seems to be a very nice tank. The glass is super thin. The bottom glass o-ring was not installed. They do give you one but it is super thin and was twisted so it would not stay in place. Here is how I got the o-ring to work. I cleaned the tank and parts in my ultrasonic cleaner with hot tap water. I put the o-ring for the glass on the outer part of the tank. Once clean I left the o-ring on the tank till it cooled. After that it installed perfect. You do have to be sure the tank does not spin while installing the upper fitting. This upper fitting also has an internal o-ring so it is going to need a bit of lube so you can hold the tank while threading it down. Once done check the bottom o-ring to make sure it is still seated. The top fill cap is very tight to turn. I think it will loosen up over time. I checked the fit on my FireBird V2 and it fits like a charm. It will not fit on the Hurricane V2.
Reviewed on Was this review helpful to you? Yes / No
NXS Styled RTA Rebuildable Tank Atomizer
NXS Styled RTA Rebuildable Tank Atomizer

Avatar
cycoblazer
Member

VERIFIED OWNER
  • JoinedJul 2016
  • Posts 108
  • Reviews 172
  • Kudos83
Overall   (5.0)
› Quality
› Value
2 of 2 people found the following review helpful
Got mine in today. Just built it with a single 3mm .5 ohm twisted 3x 28 gauge coil. Setting the coil in the center of the air slots. Worked out great. Air will run up both sides of the coil. The wicking was more than enough to fill the juice slots. The only hard part to this was getting the coils stabbed into the holes. The opposite posts make it really tight to move the coils into the post holes. Loads of air flow on this tank. Compares to my serpent mini for flavor and air flow. Nice little tank. Super nice flavor. The extra protective sleeve is nothing I will use. It fits over the 510 pin and raises the attys base off the mod. With it installed you cant adjust the airflow ring unless you take it apart. Kind of a dumb design idea. I did have some leaking but I am guessing that filling it to the top caused it. Once I stated not over filling it the leaking stopped. I would recommend this tank for D/L vaping.
Reviewed on Was this review helpful to you? Yes / No
Origen Little 16 BF Styled RTA Rebuildable Tank Atomizer
Origen Little 16 BF Styled RTA Rebuildable Tank Atomizer

Avatar
cycoblazer
Member

VERIFIED OWNER
  • JoinedJul 2016
  • Posts 108
  • Reviews 172
  • Kudos83
Overall   (5.0)
› Quality
› Value
2 of 2 people found the following review helpful
I really love this little thing. Everything fits good. It is all very tiny. It comes with the squonking pin installed. I changed it to the solid pin. This is a challenge. If you choose to do this make sure you have something under your working area to catch any small parts that may fall out while trying to get it together. I was able to build it with a single twisted 26 gauge 2.5mm wire coil. It is a bit hard but it is not super hard. Just takes a bit of practice. I found that not leaving you measuring rod in the coil makes it alot easier. Once you have it installed you can square up the coil as needed. Another thing is to keep your coil sitting high until you get your wicks tucked in. Then you can push the coil back down if needed. I really love this tank. I also bought the 22mm trim base for it. It looks ok. Much better than without if you have it on a big mod. Base is SKU: 6227600
Reviewed on Was this review helpful to you? Yes / No

Avatar
cycoblazer
Member

VERIFIED OWNER
  • JoinedJul 2016
  • Posts 108
  • Reviews 172
  • Kudos83
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
So far this has become one of my favorite tanks. The flavor and ease of building makes it a must have. The combination of having 2 decks is amazing. The quality of the machining is spot on. The finish is super nice and is not paint. No issues with the decks or making contact. I did have one o-ring that I had to replace but it has a spare in the box. Right now I am running a dual deck build at 50 watts. Super nice flavor and with my tip replacement I get little to no heat. For the price of this one I will be ordering more. Who ever made this tank did a really good job. I would recommend it to anyone that loves flavor.
Reviewed on Was this review helpful to you? Yes / No
*SALE* Authentic HCigar VT167 167W TC VW APV Box Mod
*SALE* Authentic HCigar VT167 167W TC VW APV Box Mod

Avatar
cycoblazer
Member

VERIFIED OWNER
  • JoinedJul 2016
  • Posts 108
  • Reviews 172
  • Kudos83
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
I have had this for a few weeks now. It is really nice in the hand. It has some weight to it. The functions have took me a bit to adjust to. The escribe was easy enough to link to it. This thing is all the power I needed. Fires tanks in an instant. I always seem to get the best experience for a DNA mod. It is really funny how a mod can actually change a tanks flavor but that is exactly what I notice. The finish on this mod is like a powder coat. It should be durable but I know in time it will chip. They pretty much all do dont they? Fit and finish for this mod is awesome. FOr the sale price plus the new years discount it was less than me buying a DNA 250 chip alone. HCigar did a great job on this one.
Reviewed on Was this review helpful to you? Yes / No