cory_m's Product Reviews
Sort:
Ruideng AT34 USB 3.0 Digital Multimeter Voltmeter Ammeter
Ruideng AT34 USB 3.0 Digital Multimeter Voltmeter Ammeter

cory_m
Verified

VERIFIED OWNER
  • JoinedOct 2016
  • Posts 93
  • Reviews 32
  • Kudos48
Overall   (5.0)
› Quality
› Value
PROS
Easy to use tons of information
Got this to help diagnose slow charging on a couple USB 2.0 devices, worked like a charm.
Reviewed on
Replacement Slotted Set Screw for Atomizer (50-Pack)
Replacement Slotted Set Screw for Atomizer (50-Pack)

cory_m
Verified

VERIFIED OWNER
  • JoinedOct 2016
  • Posts 93
  • Reviews 32
  • Kudos48
Overall   (2.7)
› Quality
› Value
PROS
Sometimes they are the good ones
CONS
Sometimes they are not the good ones
I had previously grabbed a 10 pack of this spec which came in a Steam Tribe baggie and were extremely well made. The 50 pack (in my case) did not fare so well and did not come in a ST bag. Out of the 48 grubs in my 50 pack, 22 of them came with outright defects - one didn't have the slot milled in at all, 2 or 3 had the slot milled off center badly enough they are unfit, the rest have huge burrs where the slot was milled. Out of the remainder, I wouldn't use about 8 or 10 due to a huge lip on the end opposite the slot giving a surface that will grab and mangle whatever is under it. The rest were OK.
Reviewed on

cory_m
Verified

VERIFIED OWNER
  • JoinedOct 2016
  • Posts 93
  • Reviews 32
  • Kudos48
Overall   (4.7)
› Quality
› Value
PROS
fairly restricted but very smooth airflow great flavor very low profile well made
CONS
cap gets hot quick if using fancy coils included drip tip is non-standard and very short
Was looking for something black to replace my silver dpro mini, saw the airflow on this one and figured it would be worth a shot - and it was everything I hoped. That said the drip tip that comes with it is stubby in both directions, puts lips too close to the top cap and most 510 drip tips will touch the coil unless you grind them down to 1 o-ring. A larger build like 28x2 with a 38 clapton at 3mm ID has the top cap heating up quickly, but this one can perform well with a 2 or 2.5mm single wire coil without quite as much heat. Only problem I had with it was, after breaking it all down to give it a scrub, getting the positive post to align so it didn't touch the top cap. Took a little fiddling with the positive post screw but was fairly easy to remedy.
Reviewed on

cory_m
Verified

VERIFIED OWNER
  • JoinedOct 2016
  • Posts 93
  • Reviews 32
  • Kudos48
Overall   (4.5)
› Quality
› Value
PROS
inexpensive fits most 810s black goes with everything
CONS
some sharp edges 810s with a oring are sometimes shorter
After spending a few minutes with some sandpaper and a leather polishing wheel on the dremel I got rid of the sharp edge at the top that I found annoying after awhile, made them perfect for my use. Shaved a little off the bottom so they seat fully down on tanks like jk mini or ftl. For whatever reason, I get far better flavor from these tips than any other 810 tip I've tried so far. They aren't flashy or fancy, I'm definitely glad I tried them though.
Reviewed on
Demon Killer 316L Stainless Steel Flame Wire for RBA Atomizers
Demon Killer 316L Stainless Steel Flame Wire for RBA Atomizers

cory_m
Verified

VERIFIED OWNER
  • JoinedOct 2016
  • Posts 93
  • Reviews 32
  • Kudos48
Overall   (5.0)
› Quality
› Value
PROS
TC or VW
I've been using this on smaller decks like KF5 to great effect (though it's a pain to trap on KF5) with temperature control. Cleans up nice with heat then water a bunch of times while rewicking before I have to change out the coil. I'll admit, this is my lazy solution some days to not wanting to make a single core clapton.
Reviewed on