shopping cart empty
Wylie's Product Reviews
Sort:

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5644
  • Reviews 77
  • Kudos3645
Overall   (4.2)
› Quality
› Value
3 of 5 people found the following review helpful
PROS
Top filling Tank options Don't have to dump fluid for adjustments or rebuilds I like the look of it
CONS
Hyped up way too much Build deck seems smaller than other Kclones Weight Lots of little parts Springs aren't that great for conductivity
What a bunch of hype. Some other variants had me contemplating purchasing the original but after experiencing previous versions and than this I'll pass on this original. The two strong points this atomizer does hold is it is able to be top filled and that the coil can be adjusted or rebuilt without dumping, syringing liquid from the tank. Those few strong points don't increase to quality of the vape and that's where I put my money.
Reviewed on Was this review helpful to you? Yes / No

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5644
  • Reviews 77
  • Kudos3645
Overall   (4.2)
› Quality
› Value
2 of 3 people found the following review helpful
PROS
Reasonable combination but the atty is outstanding with just a little work!
The device is of reasonably good quality but the atomizer shines brightly with just a little work. Drill the decks air hole just large enough for a needle bottle or syringe. Get the chrome off the positive contact at the 510 with some extra fine sandpaper, add washers to the positive screw on the deck, build a dual coil auto dripper , 8 wrap micro coil each side with 30 gauge kanthal and finally 2mm to 2.5mm holes in the cap 2 of them and call me in the morning. At just under 20 watts this produces great taste as well as loads of vapor.
Reviewed on Was this review helpful to you? Yes / No

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5644
  • Reviews 77
  • Kudos3645
Overall   (3.7)
› Quality
› Value
2 of 3 people found the following review helpful
PROS
Completely copper! Should house about any length 18650 on the market, can't speak for diameter though as I don't know. Coated copper to retain the bright finish, see cons! Air control operates well and holes are aligned fairly well. My kick fits well but I never use them and being copper I don't imagine many intend to use a kick but I count it as a plus for those whom may use them. Clean looking engraving although pretty shallow. Nice 510 threading that has fit some attys that wont fit in other devices 510.
CONS
This same coating on the copper to retain the finish was applied to the threads so it increases the voltage drop. The inner spring that retain the pins integrity through adjustment of the switches throw had to be replaced as it would let the pin fall out. .2 voltage drop on receipt in a completely copper mech mod, not so good when I can home build a mod from a water pipe with mostly brass parts and it's voltage drop is only .12! Lack of matching copper atomizers on the market. Switch lock sticks in unlocked position. Threading on the switches threads could use a lot of improvement. The threading on the battery cylinder between the main tube and the 650 tube are extremely tight, this can be taken as a pro or a con depending on how you look at it. Original springs allowed the weight of a Kayfun to cause the device to fire when stood upright on the switch.
Other than the quirks I have mentioned I'm very pleased with this product and for the amount paid verses similar options I personally think this is about the best bang for the buck in a mechanical device with potential for very low voltage drop. Keep in mind this is only my second day with this product and only about a days total use so far. Yes at this point I would suggest this device to a friend.
Reviewed on Was this review helpful to you? Yes / No

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5644
  • Reviews 77
  • Kudos3645
Overall   (3.7)
› Quality
› Value
2 of 3 people found the following review helpful
PROS
Good capacity for liquid Glass tank Stainless Easy to rebuild the coils
Both the RG200 and RG400 have surprised me, better than ProTanks 1 and 2 in my opinion.
Reviewed on Was this review helpful to you? Yes / No

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5644
  • Reviews 77
  • Kudos3645
Overall   (3.7)
› Quality
› Value
2 of 3 people found the following review helpful
PROS
Compact Nice machining Lock for switch Nice strength switch spring
CONS
Seems to be flat top battery dependent Mine had a few small scratches
Nice little 18350 device although mine showed up with some very small scratches, they'll buff out. My button head 18350 Efest IMRs either had the atty floating slightly above the cap or a small space at the switch end. I did't think an S.A.E. thread would fit but after checking I cut down a brass 10/32 screw and replaced the 510 center pin with a shorter one I made from the brass 10/32 screw.
Reviewed on Was this review helpful to you? Yes / No