shopping cart empty
Torger's Product Reviews
Sort:
Cree XM-L2 T6-3C 5000K White LED Emitter with 16mm Base
Cree XM-L2 T6-3C 5000K White LED Emitter with 16mm Base

Torger
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 3
  • Reviews 14
  • Kudos0
Overall   (5.0)
› Quality
› Value
PROS
Neutral white XML Price
Emitter seems to be as advertised. Bright and neutral light.
Reviewed on Was this review helpful to you? Yes / No
10 ohm Potentiometer / Trimpots (5-Pack)
10 ohm Potentiometer / Trimpots (5-Pack)

Torger
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 3
  • Reviews 14
  • Kudos0
Overall   (4.5)
› Quality
› Value
PROS
Adjustable trimpot The screw goes lots of rounds from all the way in to all the way out.
Used this for modding a driver circuit in flashlight. Worked out great. Now I can adjust output perfectly!
Reviewed on Was this review helpful to you? Yes / No
FUJIK Heatsink Silicone Thermal Glue (50ml)
FUJIK Heatsink Silicone Thermal Glue (50ml)

Torger
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 3
  • Reviews 14
  • Kudos0
Overall   (4.5)
› Quality
› Value
PROS
Lots of content (50ml) Easy to use Easy to center emitters since its flexible and does not dry right away
CONS
Takes many hours to dry completly
I have used this for many LEDs. It gets the job done. Using a high quality thermal paste would be better, but in some flashlights you need to make the emitter stick to the pill. This gets the job done. Now I mostly use thermal paste under the emitter and FUJIK on the sides to keep it in place. That way you can easier swap out the emitter and get maximum heat transfer. The emitter will never move and stay pressed to the pill even when you dont have a reflector or something pressing it down. This can also be used to "pot" a driver. Putting it over the circuit board and wires. That way wires will never break of where they are soldiered. Nice for certain drivers with two boards.
Reviewed on Was this review helpful to you? Yes / No
AMC7135 350mA Advanced Current Regulators - SOT-89 (10-Pack)
AMC7135 350mA Advanced Current Regulators - SOT-89 (10-Pack)

Torger
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 3
  • Reviews 14
  • Kudos0
Overall   (5.0)
› Quality
› Value
PROS
AMC7135 350mA Price
Use these for increasing current to drivers using these chips (nanjg 105c) They can be stacked on top of others too.
Reviewed on Was this review helpful to you? Yes / No
6* AMC7135 2-Group 3/5 Modes LED Flashlight Driver (Nanjg 105c)
6* AMC7135 2-Group 3/5 Modes LED Flashlight Driver (Nanjg 105c)

Torger
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 3
  • Reviews 14
  • Kudos0
Overall   (3.5)
› Quality
› Value
PROS
-Great price! -Constant current -Hidden strobe/sos -Can add or increase output current by adding/removing chips
CONS
-Whine! (This driver whines on medium, and some on low) -Medium mode is quite high. Not that much difference between that and high in perceived brightness. -Low mode could be lower -Spring is a bit short and stiff
If you are sensitive to high frequent whine, this driver can be annoying. The mode spacing is not that good. Otherwise, its a good driver. Price is great.
Reviewed on Was this review helpful to you? Yes / No