shopping cart empty
Larrykin's Product Reviews
Sort:

Larrykin
Member

VERIFIED OWNER
  • JoinedFeb 2017
  • Posts 2
  • Reviews 46
  • Kudos0
Overall   (4.0)
› Quality
› Value
2 of 2 people found the following review helpful
PROS
Reasonably leak free for an RDTA Easy to build on Simple to fill
CONS
Copper is a pain to keep clean
It's a solid, easy to use RDTA, simple to use and setup and once you have it running it will give you no problems at all as you keep topping it up without having to remove or open anything, simple unicorn bottle or similar with a long spout will go straight down the center without having to remove the cap. There's a few things you need to remember with it : 1) When you first get it, lube the seal around the middle were your push it together with a little bit of juice, it makes a big difference. 2) When it comes time to dismantle, the pin unscrews clockwise. 3) If you unscrew the top cap, it will cross thread easily when putting it back on so be careful and ensure it is lined up correctly, it shouldn't need much force. 4) If you decide to get the copper version, it discolors very easily. (develop a patina it's called) It's one of my favorite atomizers and gets used quite frequently, as for being leak free it is a dripper setup and they are supposed to stay upright, but with this setup you can invert it and it will not leak, immediately at least, I only do this when vaping heavily to ensure wick stays moist. As for cleaning the copper section, currently my easiest and quickest solution is to remove this section and remove the top cap, push it onto my finger like a ring and use some mild toothpaste to give it a polish just with your bare hands, clean it all off under the tap and dry, it only takes about 5 minutes and it's looking like new again and you don't have to worry about any chemical residue on your chamber. All in all a great unit and if I had to buy it again I would.
Reviewed on Was this review helpful to you? Yes / No
HaKKaDeal Clear Locksmith Training Practice Lock
HaKKaDeal Clear Locksmith Training Practice Lock

Larrykin
Member

VERIFIED OWNER
  • JoinedFeb 2017
  • Posts 2
  • Reviews 46
  • Kudos0
Overall   (4.0)
› Quality
› Value
PROS
Solid feel to the workings Two different combinations
CONS
Pins sitting in the curve of the case
Good lock to practice on, comes with two different keys so each side of the lock is different to the other, it is a new lock so it's going to be a bit grabby but should settle down once the corners are worn off. The only problem I had with it was the pins seemed a bit short (shorter than the picture, every lock will be different I suppose), which lead them to sit behind the curve of the case, the result of looking through the curve caused the pins to disappear slightly, working on a dark background helped them stand out a bit better though. In the end, OK Lock for the price.
Reviewed on Was this review helpful to you? Yes / No
Half-Time Drill Driver Swivel Head Quick-Change from Drilling to Driving (20 Pieces)
Half-Time Drill Driver Swivel Head Quick-Change from Drilling to Driving (20 Pieces)

Larrykin
Member

VERIFIED OWNER
  • JoinedFeb 2017
  • Posts 2
  • Reviews 46
  • Kudos0
Overall   (2.7)
› Quality
› Value
PROS
Good idea Good selection of bits & drills
CONS
The unit is made out of aluminium not steel. Poor quality
Even at this price it's not too bad for the amount of bits and drill bits with countersink collars you get. The unit itself is cheaply made, the head itself is the main problem especially as it's made out of aluminium and seemingly light grade as well. It works by having four slits down the threaded aluminium tube, which allow it to clamp down onto your bit as you tighten the collar, whilst with careful use it should be ok, too much force could cause a failure. The next problem which I have is one side the inner walls were a bit too thick, meaning the bit will not fit in, not without first carefully bending the tongues outwards slightly, which causes a different problem of the collar not having much movement as it is now too thick. In the end it works, just, it is a good idea, it's just cheaply made.
Reviewed on Was this review helpful to you? Yes / No
Magic Charcoal Comedo Nose Mask Black Head Remover Cleaner
Magic Charcoal Comedo Nose Mask Black Head Remover Cleaner

Larrykin
Member

VERIFIED OWNER
  • JoinedFeb 2017
  • Posts 2
  • Reviews 46
  • Kudos0
Overall   (3.5)
› Quality
› Value
PROS
Charcoal Does what it's supposed to do Cheaply priced
CONS
None
It's your run of the mill face mask type stuff, spread it on peel it off, it takes anything it can hold onto with it, look at all that gunk, so you know it works. This is yet another of those products riding the "it's got charcoal so it's got to be good" wave, we have soap, shampoo, toothpaste etc all with charcoal in it so why not a nose mask. Who's going to be first Pepsi or Coca Cola to cash in on it hmmm.... Anyway it does what it's supposed to, unless you can read Chinese don't bother with the instructions, it's pretty simple though, just like all the others : Hot water first to open your pores. Spread on affected area (doesn't have to be just your nose). Wait 10-20 minutes depending on how thick you decided to spread it (don't need to waste it, only needs to be thick enough so it will hold together as you peel it). Peel it all away and then wash with cold water to close those pores before they start collecting dirt again. Have fun showing off your new cleaner face.
Reviewed on Was this review helpful to you? Yes / No
3-10mm High Speed Steel 5 Flute Countersink Drill Bit Tapper Tool (7 Pieces)
3-10mm High Speed Steel 5 Flute Countersink Drill Bit Tapper Tool (7 Pieces)

Larrykin
Member

VERIFIED OWNER
  • JoinedFeb 2017
  • Posts 2
  • Reviews 46
  • Kudos0
Overall   (2.0)
› Quality
› Value
PROS
Cheaply priced Countersink collars can be used on other drill bits
CONS
Cheap Cheap Cheap
You can't really expect too much at this price, upon close inspection of each item you can see it has been cheaply made, my set also tuned up with at least some slight bend in a drill. 4 items were off center by 1mm, the other three items were off by 2mm, 3mm & 5mm, and these were the bigger bits that had the larger bends, not the smaller bits as you might have thought. In the end I ended up with some drill bits and at worse at least the countersink collars can be used on other drill bits. Fasttech at least did their part to fix the problem, they're good like that.
Reviewed on Was this review helpful to you? Yes / No