shopping cart empty
Haylingbrian's Product Reviews
Sort:

Haylingbrian
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 945
  • Reviews 190
  • Kudos704
Overall   (5.0)
› Quality
› Value
0 of 2 people found the following review helpful
I keep buying them and now have quite a few - the ONLY atty I use. Have tried the rest, and stuck with the best !! No complaints or faults with any I have bought.
Reviewed on Was this review helpful to you? Yes / No

Haylingbrian
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 945
  • Reviews 190
  • Kudos704
Overall   (5.0)
› Quality
› Value
0 of 2 people found the following review helpful
These tips are possibly the best looking I've had off here. Set off a black/stainless mod and atty set up perfectly.
Reviewed on Was this review helpful to you? Yes / No

Haylingbrian
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 945
  • Reviews 190
  • Kudos704
Overall   (5.0)
› Quality
› Value
0 of 2 people found the following review helpful
I wanted small bottles to do trial mixes/blending and these fit the bill perfectly - no complaints from me.
Reviewed on Was this review helpful to you? Yes / No
Empty Dropper Bottles for E-liquids (5-Pack / 30ml)
Empty Dropper Bottles for E-liquids (5-Pack / 30ml)

Haylingbrian
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 945
  • Reviews 190
  • Kudos704
Overall   (2.2)
› Quality
› Value
0 of 2 people found the following review helpful
PROS
nice and squeezy
CONS
inserts too big to fit hole in bottle
What a major flaw - great bottles and just what I wanted - if only the dropper inserts were't too big to fit the bottle. Luckily I have enough spare dropper caps to overcome this problem but come on FT - that is a fundemantal flaw to say the least....
Reviewed on Was this review helpful to you? Yes / No

Haylingbrian
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 945
  • Reviews 190
  • Kudos704
Overall   (4.7)
› Quality
› Value
1 of 4 people found the following review helpful
PROS
Solid Good threads Looks good Locking ring and airflow
CONS
Some battery rattle Non-insulated bottom cap Takes a bit of setting up initially, you CAN'T use it without doing some.
Received this today after a reasonable and acceptable 15 days from order to delivery. Well worth the wait as far as I'm concerned. I have read other reviews and accept that while it doesn't work out of the box without adjustments, the required ones were simple to figure out. These are my observations and fixes which I hope some will find helpful. Locking ring - locked tight in the 'on' position, but a bit of pressure released it and works as it should very smoothly. Mine is reverse threaded - have I been lucky ? Battery rattle - solved with a couple of turns of tape. 510 fitting/firing pin - I also went straight in screwing on (or trying to) an atty. Wouldn't go down more than 2 turns and then started to cross thread. Had a look inside and realised the adjustable pin was in the fully raised position so again with slight pressure I was able to loosen and retract it enough to allow me to fully screw on an atty, but it didn't sit flush. With a little more pressure the brass centre pushes down slightly allowing the atty to sit flush.You then need to adjust the firing pin to suit your battery - move it in just enough to break contact with the battery and give a good switch throw. Also noticed the previous problem re the airflow but with my attys its not an issue but as and when I need to use it I will have a fiddle to see if I can figure out a fix.... Job done and have in my hand an absolute steal of a mod which looks the absolute dogs doo-dahs topped with my Kayfun. Oh - also hits like a train !
Reviewed on Was this review helpful to you? Yes / No