shopping cart empty
HarleyQuin's Product Reviews
Sort:
4* AMC7135 2-Group 3/5 Modes LED Flashlight Driver (Nanjg 101-AK-A1)
4* AMC7135 2-Group 3/5 Modes LED Flashlight Driver (Nanjg 101-AK-A1)

HarleyQuin
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 22
  • Reviews 44
  • Kudos6
Overall   (4.7)
› Quality
› Value
3 of 3 people found the following review helpful
A very good single sided AMC7135 driver. As it has no stars it fits pills with a retaining ring better than the 3* Nanjg AK-47A - and has one 7135 more. It even has the 4 groups as Nanjg AK-47A or Nanjg 105c, just connect the right pin on top to ground (LoHiStrobe) or the 2nd from left on bottom to ground (LoHi). Works flawless. UI is like the 105c, and of course it has the dreaded PWM-whine on Med (very audible) and Lo (slightly audible).
Reviewed on Was this review helpful to you? Yes / No
Measy RC12 2.4GHz Wireless Fly Air Mouse + Keyboard Set
Measy RC12 2.4GHz Wireless Fly Air Mouse + Keyboard Set

HarleyQuin
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 22
  • Reviews 44
  • Kudos6
Overall   (5.0)
› Quality
› Value
3 of 3 people found the following review helpful
I use this simply as a wireless keyboard and mouse to operate the PC. It works terrific. I have used other solutions before and this one simply works. Plug and play unter Windows 7 and Windows XP, I did put the receiver in a free USB socket, preferably in sight with the keyboard, and it worked at 1st try. The receiver can be stored in the keyboard, which is good if you change between different PCs. The back cover holds firmly, but can be opened with a thumbnail. Keyboard goes to standby fairly quick, pressing any button wakes it up. Range is at least 11 meters with full battery and direct sight to the receiver. This is the case with Alkalines (1.5V) and Eneloops (1.2V NiMH). There is minor room for improvement: The touchpad is recessend a bit much (3.2mm) and as it is small, there's not much room to operate. It works, but would be better if it was sitting higher. The red off button (top row, 2nd to the left) shuts down the PC without asking confirmation. And this button is easily confused with the Esc-button in the dark. I can say nothing to the integration of the various multimedia function buttons, as I use this one only under normal Windows OS. But for that: Highly recommended.
Reviewed on Was this review helpful to you? Yes / No
FandyFire HD2010 5-Mode LED Flashlight (3.1A Version)
FandyFire HD2010 5-Mode LED Flashlight (3.1A Version)

HarleyQuin
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 22
  • Reviews 44
  • Kudos6
Overall   (5.0)
› Quality
› Value
3 of 3 people found the following review helpful
This is the real deal. Very good build quality, emitter glued but well centered, all o-rings intact. Tint is a blueish cold white which I prefer over a greenish one. Driver works well, direct drive on high which produces a solid 4.9A with my best cell. This gives a great throw. The sheer amount of material of the body handles the heat extremely well. Blinky modes are a nuisance, as always. No memory, so it always starts on high after being turned off for several seconds. Anodization is flawless. Knurling could be more aggressive to help singlehanded operation. But it's the same knurling as in other HD2010s, so this was to be expected. Pill is aluminium, not very modding friendly, but doable. 20mm emitter don't fit without heavy dremeling, 16mm work. All in all a very good single cell light.
Reviewed on Was this review helpful to you? Yes / No
Goot Wick Soldering Remover (2.0mm x 1.5m)
Goot Wick Soldering Remover (2.0mm x 1.5m)

HarleyQuin
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 22
  • Reviews 44
  • Kudos6
Overall   (4.5)
› Quality
› Value
3 of 3 people found the following review helpful
I mainly use it to copper-braid the springs of my flashlights and for that it is just perfect because it does not have any flux on it. The solder does not flow up the copper-mesh that fast. Consequently using it to remove solder is less than perfect - it works, but you'd really wish for flux on it.
Reviewed on Was this review helpful to you? Yes / No
Chips Repair Tool Soldering Paste Grease
Chips Repair Tool Soldering Paste Grease

HarleyQuin
Member

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 22
  • Reviews 44
  • Kudos6
Overall   (4.5)
› Quality
› Value
2 of 2 people found the following review helpful
Seems to be the cheapest solder paste on the market. Very good for reflow soldering with a rework station. The container comes well sealed. The paste can be filled into a syringe, I recommend a slim 1mm syringe to assemble PCBs. The package is only 1/4 filled, I presume that's why the paste gets too thick for syringe use after several weeks. Just add one or two drops of solder flux and stir, that way you can get exactly the viscosity you need.
Reviewed on Was this review helpful to you? Yes / No