
GeekVape 2-in-1 A1/N80 Wire (8-Pack)
|
Frin70
Verified
VERIFIED OWNER
- JoinedMay 2017
- Posts
605
- Reviews
24
- Kudos229
|
Overall
|
(4.7)
|
› Quality
|
|
› Value
|
|
PROS
Great taste
Easy to work with
included tool
Ohms out almost as described
Clean
|
CONS
Nothing much I can think of
|
The pro's and con's basically say it all, its a coil after all.
Its 4 wraps just FIY, the other one is 5 wraps, but the leads are long enough to do 2 more wraps
Reviewed on
|
|

Oumier Wasp Nano Mini RDA Rebuildable Dripping Atomizer
|
Frin70
Verified
VERIFIED OWNER
- JoinedMay 2017
- Posts
605
- Reviews
24
- Kudos229
|
Overall
|
(5.0)
|
› Quality
|
|
› Value
|
|
PROS
Flavor
Lots of air for a single coiler
Easy of building
510 drip tip adapter is the drip tip
Squonk friendly as heck
Easy as heck to rewick
Great for juice testing
|
CONS
lots of air for a single coiler
Small well but its a 22mm so yeh
Spitback galore if not wicked properly but thats to be expected
|
Use the Scottish roll method (there are tons of tutorials on YouTube for it) and you will remove the issue. You have to build spaced coils unless the coil you are using is chunky, but I wouldnt recommend that.
As for coil height, I would recommend a bit higher coil, as in, when you look through the air slot, you have to see the bottom of the coil.
Can be turbulent and whistly but that depends on the build you have in it. Micro coils dont whistle but fused do, so go figure. Im using this ultem one for juice testing and the black one is in squonk mode for squonking all the time.
Reviewed on
|
|

Resin 510 Drip Tip
|
Frin70
Verified
VERIFIED OWNER
- JoinedMay 2017
- Posts
605
- Reviews
24
- Kudos229
|
Overall
|
(5.0)
|
› Quality
|
|
› Value
|
|
PROS
Colors
Smaller bore perfect for MTL style
In the middle of it, its domed
|
CONS
Flavor a tad lost but its still really great for MTL
|
Great little drip tip, fits most of my (except for clones but its clones so who cares?) RDA's/RTA's. Do keep in mind, these are for MTL more suited than for DTL, in DTL its too tight and I lose 30% ish flavor.
Reviewed on
|
|

Oumier Wasp Nano RDA Rebuildable Dripping Atomizer
|
Frin70
Verified
VERIFIED OWNER
- JoinedMay 2017
- Posts
605
- Reviews
24
- Kudos229
|
Overall
|
(5.0)
|
› Quality
|
|
› Value
|
|
PROS
Flavor
Lots of air for a single coiler
Easy of building
510 drip tip adapter is the drip tip
Squonk friendly as heck
Easy as heck to rewick
Great for juice testing
|
CONS
lots of air for a single coiler
Small well but its a 22mm so yeh
Spitback galore if not wicked properly but thats to be expected
|
Use the Scottish roll method (there are tons of tutorials on YouTube for it) and you will remove the issue. You have to build spaced coils unless the coil you are using is chunky, but I wouldnt recommend that.
As for coil height, I would recommend a bit higher coil, as in, when you look through the air slot, you have to see the bottom of the coil.
Can be turbulent and whistly but that depends on the build you have in it. Micro coils dont whistle but fused do, so go figure. Im using this ultem one for juice testing and the black one is in squonk mode for squonking all the time.
Reviewed on
|
|
![]()
|
Frin70
Verified
VERIFIED OWNER
- JoinedMay 2017
- Posts
605
- Reviews
24
- Kudos229
|
Overall
|
(4.0)
|
› Quality
|
|
› Value
|
|
PROS
Great for phones which are thinner
|
CONS
Wont hold the likes of the S8 with a thicker case
|
Really good, did a test run with my broken Z5 from Sony and it held up well in rough terrain. But again, get a thinner phone case if yours is too thick. And you can always try to pull out your phone with a fast pull to see how much it will hold up
Reviewed on
|