Cynok03's Product Reviews
Sort:

Cynok03
Verified

VERIFIED OWNER
  • JoinedJan 2017
  • Posts 11
  • Reviews 47
  • Kudos5
Overall   (5.0)
› Quality
› Value
PROS
-Well machined
CONS
-Holes in the peek deck insulator are too small
I got both 24mm and 22mm from Kindbright and it's the best clones you can get... My preference is for the 24mm version but the 22mm is very nice... I put a 510 driptip in the original drip tip : Flavour is even better and no heat problem. TRY IT YOU WILL UNDERSTAND You have to enlarge the holes in the peek deck insulator (slowly hand drilled with a slightly larger drill bit)
Reviewed on
Thunderhead Creations Kanthal A1 Heating Wire for RBA Atomizer
Thunderhead Creations Kanthal A1 Heating Wire for RBA Atomizer

Cynok03
Verified

VERIFIED OWNER
  • JoinedJan 2017
  • Posts 11
  • Reviews 47
  • Kudos5
Overall   (5.0)
› Quality
› Value
Good clean wire... I recommend it.
Reviewed on
XFKM Kanthal A1 + 316L Stainless Steel Alien V2 Pre-Coiled Wire
XFKM Kanthal A1 + 316L Stainless Steel Alien V2 Pre-Coiled Wire

Cynok03
Verified

VERIFIED OWNER
  • JoinedJan 2017
  • Posts 11
  • Reviews 47
  • Kudos5
Overall   (5.0)
› Quality
› Value
PROS
-Well made -Great flavour and vapor production
I use them in dual coil, works like a charm. Getting good flavor from them. Accurate resistance.
Reviewed on

Cynok03
Verified

VERIFIED OWNER
  • JoinedJan 2017
  • Posts 11
  • Reviews 47
  • Kudos5
Overall   (5.0)
› Quality
› Value
PROS
-Great surface -Easy to work -Easy to clean -Lasts very long -Very good rendering of flavors
CONS
-None
Add half a wrap to have full 4 wraps (with 14mm total leg length) gives .27ohm with ID 3mm. Heats up quickly even on a mech...
Reviewed on
Demon Killer Staple Staggered Fused Clapton Pre-Coiled Wire for RBA Atomizer (10-Pack)
Demon Killer Staple Staggered Fused Clapton Pre-Coiled Wire for RBA Atomizer (10-Pack)

Cynok03
Verified

VERIFIED OWNER
  • JoinedJan 2017
  • Posts 11
  • Reviews 47
  • Kudos5
Overall   (4.5)
› Quality
› Value
PROS
Clean Good flavor Long lasting
CONS
Not really 0.3ohm (but around 0.4ohm)
One of my favorite 3mm ID coil for The Flave Tank. The resistance act almost like a 3*28/32AWG Alien coil in kanthal core/SS outer Here my setups : -I just wrap a half more to get the legs in the opposite side and i read 0.45ohms (5 wraps)... Cool vape to use with airflows 80% closed : best flavor (TRY IT ^^) -I unwrap a half to get the legs in the opposite side and i read 0.38ohms (4 wraps)... Warmer vape to use with airflows 80%-100% open : best clouds It's a light version of a Staple Staggered Fused Clapton (with only 2 flat wires) It's perfect for a single 18650 mech because ramp up time is not very long... I simply pulse them a little (no real dry burn) and brush them under warm water between each change of wicks
Reviewed on