WORLDWIDE FREE SHIPPING
![]()
|
Swetnam1
Verified
VERIFIED OWNER
- JoinedApr 2020
- Posts
15
- Reviews
55
- Kudos3
|
|
Overall
|
(3.2)
|
| › Quality
|
|
| › Value
|
|
|
PROS
flavour
|
|
CONS
hard to build and fill
|
flavour is good for mtl but this is not the easiest to build and filling is also bad, i reccomend modifying the fill hole with a drill
Reviewed on
|
|
![]()
|
Izme_ma
Verified
VERIFIED OWNER
- JoinedAug 2020
- Posts
1
- Reviews
6
- Kudos0
|
|
Overall
|
(3.0)
|
| › Quality
|
|
| › Value
|
|
au départ Je l'est pris uniquement comme pièces de rechange,mais utilisable a condition de :
•d'enlever lavis pôle positif et limer PEEK d'isolation au niveau ( trop long imposible de serrer le fil)
•la vis connecteur 510 est réglable( enlever la base, la bague laiton est amovible)
•oring a remplacer,peek de très mauvaise qualité se deforme rapidement a changer.
Bref je voulais l'utiliser comme pièces de recharge,principalement le tank _ compatible clone zest 2.2) mais pas zest 2.2 urs yftk
YFtk(filetage bague air différant comme d'habitude avec yftk) vous pouvez l'utilise avec sa bague mais je vouse conseille d'avoir des o ring de diferente taille pour ajuster ( diamètre intérieur de 11 à 15 1mm premier base FKM le second NBR) utilisable egalement avec melapous +
Personnellement je l'utilise sans problème.des clone GUS Y'a largement mieux à environ 20/30$
Reviewed on
|
|
![]()
|
RL...
Verified
VERIFIED OWNER
- JoinedApr 2021
- Posts
0
- Reviews
1
- Kudos0
|
|
Overall
|
(3.2)
|
| › Quality
|
|
| › Value
|
|
|
PROS
Nice taste, cheap.
|
|
CONS
Inner + has no contact to bottom-screw, have to fix it. Not easy to build.
|
Intermediate mtl, nice taste. No leaks, simple construction. Average build quality.
Reviewed on
|
|
![]()
|
Troublemaker
Verified
VERIFIED OWNER
- JoinedMar 2017
- Posts
0
- Reviews
7
- Kudos0
|
|
Overall
|
(2.0)
|
| › Quality
|
|
| › Value
|
|
|
PROS
Look, price
|
|
CONS
Can't install coil
|
Between the 2 screw heads are 2mm space. If you try to tighten up the screw to secure the coil it didn't fit under the screw head and jumps away! If you wanna tighten up the screw with the isolator, it spins free because the screw hole isn't secured on the bottom. Except this it's a good looking atomizer but because of this problems totally useless!!
Reviewed on
|
|
![]()
|
postNuKe
Verified
VERIFIED OWNER
- JoinedDec 2019
- Posts
8
- Reviews
3
- Kudos5
|
|
Overall
|
(3.7)
|
| › Quality
|
|
| › Value
|
|
|
PROS
cheap
Great with Latakia flavour tobacco
|
|
CONS
sharp some places
|
It is inexpensive so if you change the drip tip with this https://www.fasttech.com/p/1623501 you are going to take an awesome experience with Latakia flavour tobacco. This atty is perfect with this e-liquid. You should clean with a special tool the sharp when you twist the tank with the deck. Maybe change the o-rings and It's done.
Reviewed on
|
|
![]()
|
DobiStyle
Verified
VERIFIED OWNER
- JoinedJul 2016
- Posts
1
- Reviews
41
- Kudos0
|
|
Overall
|
(4.2)
|
| › Quality
|
|
| › Value
|
|
|
PROS
Вкусный, очень вкусный сигаретник.
|
|
CONS
Очень маленькое отверстие заправки (рассверлил до 3мм, стало гораздо удобнее).
Фиксация плюсовой стойки - это ахтунг. Пришлось разбирать базу и колхозить, что бы не вращалась при фиксации спирали.
Укладка ваты требует аккуратности.
|
За текущую цену, если хочется попробовать что-то новое и руки из нужного места, можно и купить.
Поигрался и подарил камраду.
Reviewed on
|
|
![]()
|
mocarela
Verified
VERIFIED OWNER
- JoinedOct 2018
- Posts
0
- Reviews
3
- Kudos0
|
|
Overall
|
(2.7)
|
| › Quality
|
|
| › Value
|
|
|
PROS
cheap
easy to rebuild
nice looking
|
|
CONS
not optimal design
leaking
little airflow
small filling holes
|
The atomizer is not perfect, but definitely you get more than you paid for.
IMHO neither the original one should be much better - it's a design problem.
Sealing relies only on bottom and top o-rings and nobody can't expect they do their job without leaking if corresponding pieces has to be taken apart.
Also, there is almost no airflow (only usable for MTL) and the airflow control ring can be spun too easy.
The filling holes are so small they can be used only with needle.
Apart of the above issues it is quite OK considering the price.
Reviewed on
|
|
![]()
|
 DaddyDead
Verified
VERIFIED OWNER
- JoinedFeb 2015
- Posts
3151
- Reviews
302
- Kudos5400
|
|
Overall
|
(1.2)
|
| › Quality
|
|
| › Value
|
|
|
PROS
Cheap
Looks OK
|
|
CONS
Tricky to build right
Tricky to fill right
Nothing to make me use it twice
|
Based on other atty's but not done as well ... poor build quality (spinning screws)and poor clamping means that even getting a coil in right is a total faff that no one needs
Flavor is OK but not great and filling, while seeming simple is really a pain as port at top are to small and taking the tank off is to messy.
They got the look right but for me its a one use and toss
Reviewed on
|
|
![]()
|
filorp
Verified
VERIFIED OWNER
- JoinedFeb 2014
- Posts
246
- Reviews
187
- Kudos65
|
|
Overall
|
(3.2)
|
| › Quality
|
|
| › Value
|
|
|
PROS
prise
good flavour
|
|
CONS
shorted straight from the box
afc doesn't work
refill holes are to small
|
Really can't complain for $3.5... It arrive shorted due to press fit positive pine that has been pushed to far in the factory. One of the air holes is not drilled through properly. The juice holes for refilling are to small. Fixed everything. Afc ring is to large hence afc doesn't work properly, air control is basically non existent. But as I said hard to complain for the prise.
Reviewed on
|
|
![]()
|
DippyDuckEgg
Verified
VERIFIED OWNER
- JoinedNov 2015
- Posts
27
- Reviews
98
- Kudos16
|
|
Overall
|
(5.0)
|
| › Quality
|
|
| › Value
|
|
|
PROS
doesn't leak
|
|
CONS
a bit tricky to build
510 contraption spins in the base
|
not a bad tank to play with, don't think it will replace my favourite dvarws though
Reviewed on
|