shopping cart empty
Product Reviews
WORLDWIDE FREE SHIPPING
5-pack


Sort:
Ivory_Tickler
Member

VERIFIED OWNER
  • JoinedJun 2013
  • Posts 3
  • Reviews 1
  • Kudos1
Overall   (1.2)
› Quality
› Value
5 of 5 people found the following review helpful
PROS
NONE
CONS
does not fit: kanger protank, kanger protank mini, evod tanks(sold here)
ordered for my kanger tanks (protank, protank mini, evod), but none of them fit. they are the longer ones(even though the picture in the review section shows the shorter) so i figured they at least fit the protanks. The tanks will not close shut. It seems the clear rubber seals are preventing it to close. So I removed them and replaced them with the rubber seal from my other evod cores and I was able to close the tank(w/ a tiny gap, but still was able to close). However, there was a burnt taste that never went away. These don't even fit the protank clone, x9 protank.

I would like to exchange or return, but I already used 2 out of my 5 pack so it seems the product as a whole does not qualify for this exchange or return. Anyone know what tanks these would fit? Any help from Fasttech would be appreciated.
Reviewed on Was this review helpful to you? Yes / No
zarfy
Member

VERIFIED OWNER
  • JoinedJul 2013
  • Posts 904
  • Reviews 343
  • Kudos543
Overall   (3.5)
› Quality
› Value
2 of 2 people found the following review helpful
PROS
price easily rebuildable
CONS
little o-rings easy to lose silicone gasket is a bit fragile (tears easily)
not bad. good price. will, and do, buy more - ever so often.
Most resistances are within 0.2 ohms of claimed values.

---

I initially used these to replace evod coils which had "peaked" and found that these worked fine.

Once I had a small stockpile of "peaked" coils, those got re-built, cannibalising parts as needed.

I try to buy a 5-pack every few months to replenish needed parts - after using them first - as the gaskets and insulators can get torn/damaged, becoming unusable.

OT: On any BC atty I have (evod,protank,RGxx,etc), I rebuild using a solid (i.e. tightly rolled) stainless steel (SS) mesh wick, with small tightly-rolled boiled-cotton wads to minimise BCC "gurgle" and also to reduce chance of circular metal stem shorting on coil. Most times (4 out of 5, I'd say) I can rebuild with no gurgle, and using SS improves wicking dramatically compared to silica, with no dry hits (as long as there's ejuice in the tank)...

---

All machined items, like these, should get steeped in warm water and citric acid (IPA is prob better) for an hour or two (if all metal parts then boiled water is ok, else just warm ). Then they should be thoroughly rinsed, and air-dried for a day or two before use as , early on, I happened on one that imbued a foul taste to the vape.
(once bitten,etc... never happened again - coz every such item now gets well-cleaned before use)

ps. don't leave o-rings to steep in water with citric acid for too long ( 2 or 3 hours is enough - no more) as they can get damaged if left for too long. (memories of a long weekend away, to return and find forgotten steeping o-rings distended to about twice their normal size... :( )
Reviewed on Was this review helpful to you? Yes / No
Avatar
kotoklizm
Member

VERIFIED OWNER
  • JoinedSep 2014
  • Posts 0
  • Reviews 90
  • Kudos0
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
nice cores, cheap and good. definitely
Reviewed on Was this review helpful to you? Yes / No
Cola79
Member

VERIFIED OWNER
  • JoinedSep 2014
  • Posts 2
  • Reviews 5
  • Kudos1
Overall   (0.5)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
-None
CONS
-awful taste right from the start -false ohm rating (+0,7 to +1 ohms more) -bottom rubber ring falls apart easily
I will not buy these again and do not recommend these to anyone. First of all, they have an awful taste right from the start, like chewing on a cotton ball. This bad taste is so dominant, that none of your liquid flavor gets through. And yes, i let the liquid soak in for about 7 minutes before...

The ohm rating is complete wishful thinking, the coils i ordered should come with 2 ohm, but the ones i received show ohm ratings from 2,7 to 3 on my Vamo (which shows normally correct ohms with the original coils i used so far).

The bottom ring falls apart by itself already inside the pack, just that much about build quality...

I am deeply disappointed with my purchase. Such a bad product, really! I wonder if these do harm to your health, because the awful taste must come from somewhere, probably the used materials are questionable...
Reviewed on Was this review helpful to you? Yes / No
GuntherSlunt
Member

VERIFIED OWNER
  • JoinedFeb 2014
  • Posts 37
  • Reviews 162
  • Kudos7
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
- Longer post, works in more of my clearomizers - Very economical, great value - After a little research, discovered they are super easy to rebuild as well
CONS
- Easy to lose the bottom o-ring if you are easily distracted (like myself) - None!
Bought these to replace the heads in my Mini Davide and H2 Clearomizers. They work great, no complaints. I find them incredibly easy to rebuild, especially if you were to pair them with something like SKU 1591601. FastTech, thanks for saving me a lot of cash!
Reviewed on Was this review helpful to you? Yes / No
Tanaque
Member

VERIFIED OWNER
  • JoinedSep 2013
  • Posts 9
  • Reviews 31
  • Kudos3
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
Price Quality
CONS
Ohms greater than specified 2.0
Good product for the price. Can't go wrong with this. they work with both my MT3 and Puritank tanks.
Reviewed on Was this review helpful to you? Yes / No
stels
Member

VERIFIED OWNER
  • JoinedOct 2013
  • Posts 5
  • Reviews 164
  • Kudos1
Overall   (3.0)
› Quality
› Value
not so good, expecting better quality
Reviewed on Was this review helpful to you? Yes / No
VapersPro
Member

VERIFIED OWNER
  • JoinedDec 2015
  • Posts 2
  • Reviews 6
  • Kudos0
Overall   (4.5)
› Quality
› Value
PROS
Build Flavor
CONS
some has more resistance.
nice cores, nice build, nice silica in there.
Reviewed on Was this review helpful to you? Yes / No
Araiser
Member

VERIFIED OWNER
  • JoinedAug 2013
  • Posts 38
  • Reviews 54
  • Kudos1
Overall   (5.0)
› Quality
› Value
PROS
Good quality
Good taste, good cloud as for Evod.
Reviewed on Was this review helpful to you? Yes / No
420chris
Member

VERIFIED OWNER
  • JoinedJul 2014
  • Posts 42
  • Reviews 126
  • Kudos18
Overall   (5.0)
› Quality
› Value
PROS
The price They work well
CONS
None
The price is good.
They work well.
Reviewed on Was this review helpful to you? Yes / No