Product Reviews
WORLDWIDE FREE SHIPPING


Sort:
OlyaKr
Verified

VERIFIED OWNER
  • JoinedFeb 2013
  • Posts 1
  • Reviews 208
  • Kudos0
Overall   (5.0)
› Quality
› Value
Товар целиком и полностью соответствует своему описанию на сайте, всё доставляется в хорошо упакованном виде. Драйвер покупался для фонарика Ultrafire С8, работает хорошо.
Reviewed on
diyau
Verified

VERIFIED OWNER
  • JoinedJan 2013
  • Posts 17
  • Reviews 13
  • Kudos2
Overall   (5.0)
› Quality
› Value
PROS
- Customizable mode groups - Very efficient (driver outputs minimum heat) - Well spaced modes - Can be driven very well and max output is very close to 2800mA!
CONS
- Very small PWM noise when operating on medium mode (not noisy or noticeable at all!! shouldn't be a con!)
Very capable and great driver. Features a small +ve spring soldered on the back which is very convenient. Also has customizable group drivers by soldering a specific star to the ground which is easy to do. Definitely recommend this!! I used this driver in conjunction with (SKU: 1122302 XML T6-3C 5000K EMITTER) and C20 DIY CREE Flashlight Body (SKU 1181700 ). This makes a very bright compact thrower and also has a perfect balance between throw and flood. Light is driven at approx. 2A high, 1A medium and 100mA low with this driver Great use!!
Reviewed on
focus74
Verified

VERIFIED OWNER
  • JoinedApr 2015
  • Posts 0
  • Reviews 44
  • Kudos0
Overall   (5.0)
› Quality
› Value
PROS
возможность подобрать требуемый ток, выпаиванием нужного количества стабилизаторов (8*350), возможность прошивки контроллера, спаяно все качественно.
На форуме фонаревки много вариантов прошивки этого драйвера, хоть под силовую, хоть под тактовую кнопку, с реализацией степдауна по температуре светодиода, можно сделать линейник с минимальной переделкой, или шим вообще без переделки. выпаяв лишние стабилизаторы можно подобрать требуемый ток от 350мА до 2800мА кратно 350мА (ток одного стабилизатора)
Reviewed on
Alistair138
Verified

VERIFIED OWNER
  • JoinedNov 2014
  • Posts 0
  • Reviews 9
  • Kudos0
Overall   (5.0)
› Quality
› Value
PROS
Cheap Well made for what its worth Reasonably high amp output
CONS
Wires are very thin The wire connecting points are on IC legs, and in tight places so replacing is a bit messy job.
Using it with Cree XM-L U3-1C. All modes work, all different sets of modes work. Puts on a nice amp output. A little bit of whirring and buzzing when on part-bright modes (10%, 50%). After 2.9 volts the flashlight starts to flash once a second - not an nice way to signal a dead battery - some drivers just dims to lowest mode so you really can exit the dark room. But anyway definetely worth its money.
Reviewed on
Mironov_IA
Verified

VERIFIED OWNER
  • JoinedFeb 2014
  • Posts 0
  • Reviews 8
  • Kudos0
Overall   (5.0)
› Quality
› Value
Можно брать и не думать в другую сторону!!!
Reviewed on
buyer70
Verified

VERIFIED OWNER
  • JoinedMar 2013
  • Posts 0
  • Reviews 52
  • Kudos0
Overall   (4.0)
› Quality
› Value
PROS
Downgradeable Comes with spring
CONS
Wires Whines (~4.5kHz) in PWM modes (low, medium) Need very good battery
Almost useless with all my batteries including popular Sanyo UR18650FM. I think to remove a couple of AMCs to reduce the current.
Reviewed on
nztdm
Verified

VERIFIED OWNER
  • JoinedMar 2013
  • Posts 0
  • Reviews 3
  • Kudos0
Overall   (4.2)
› Quality
› Value
PROS
2800mA is perfect XM-L Current Selectable modes configs via solder jumpers very thin, no big inductors Strong, short battery spring
CONS
Linear driver, makes heat Flashes when battery is low way too early No selection for 1-mode
This is the best XM-L driver I have seen yet, almost 10/10, just needs to fix the flashing problem.
Reviewed on
frnky
Verified

VERIFIED OWNER
  • JoinedMay 2015
  • Posts 4
  • Reviews 4
  • Kudos2
Overall   (4.2)
› Quality
› Value
PROS
2.8 amp output Based on an ATtiny MCU which you can reprogram quite easily
CONS
MODES — no matter which stars you short, there's always at least two modes There are some serious issues when trying to use it in a Convoy S2+
Alas, this driver doesn't fit in a Convoy S2+ body.

First, two of the bottom 7135s are positioned OVER the ground rim and leave no room for the ring that's supposed to secure the driver. The thing is, they could move the chips just a little bit to completely avoid this!

Second, the spring is too short/weak for the bottom switch to activate when the copper part with the LED is screwed all the way in, which you have to do to secure the reflector. Make sure to order some 8x10mm springs and be ready to do some soldering.

Third, this jumper config system is a joke. What I want from a flashlight is to just turn on and off — no modes; and there's no jumper for this. Good thing you can reprogram it, but
Reviewed on
ts989
Verified

VERIFIED OWNER
  • JoinedOct 2018
  • Posts 0
  • Reviews 21
  • Kudos0
Overall   (4.7)
› Quality
› Value
PROS
Price Reliability Comes with silicone wires
Reliable driver module for single cell li-ion lights
Reviewed on
slavianr
Verified

VERIFIED OWNER
  • JoinedApr 2015
  • Posts 0
  • Reviews 64
  • Kudos0
Overall   (5.0)
› Quality
› Value
хороший линейный драйвер, поставил и забыл
Reviewed on