shopping cart empty
WORLDWIDE FREE SHIPPING

Best build for mech squonker
Login to post a new topic and to write a reply.
Thread Tools Rate This Thread


Search within thread:

Login to rate this thread.
#1 (permalink)      4/13/2017 4:10:03 AM US Central   quote/reply + tips
Ukkev
Member
  • JoinedJun 2013
  • Posts 100
  • Reviews 0
  • Kudos47
+1 details
Best build for mech squonker
What's everyone recommend build for this, not found one I'm happy with yet ?
#2 (permalink)      4/15/2017 6:29:35 AM US Central   quote/reply + tips
Avatar
foxey
Member
  • JoinedJun 2013
  • Posts 3799
  • Reviews 87
  • Kudos2968
+1 details
I personally think and use a basic micro / spaced coils for all bottom fed drippers, also i use s/s wicks on my origens which have been converted to bottom fed for tabacco / cigar flavours, they are nice crisp tasting , flavour over clouds is the key word 😋
I told you so !
#3 (permalink)      4/24/2017 1:42:08 PM US Central   quote/reply + tips
tonypo
Member
  • JoinedFeb 2016
  • Posts 4
  • Reviews 6
  • Kudos4
I've built a kanthal 26/35 clapton in mine... 6 wraps around 3mm, and it works very well.
I did drill out the airhole to give about 2mm diameter though. A setup I am finding giveing better results than my Origen 16 tiny on flavour. I vape inbetween MTL and DLH, or maybe best described as very open MTL.
#4 (permalink)      5/2/2017 6:30:01 PM US Central   quote/reply + tips
Hawki
Member
  • JoinedAug 2013
  • Posts 704
  • Reviews 5
  • Kudos318
I'be been building 26 ss 8wrap. 55.
Fish are dum dum dum. They chase anything that glitters(beginners)
#5 (permalink)      5/4/2017 3:59:38 PM US Central   quote/reply + tips
monocle
Member
  • JoinedDec 2016
  • Posts 55
  • Reviews 4
  • Kudos10
These are mech builds. First one works on 18350 battery the whole day for me. Tight draw of cource.

K1 0.32@2, 6 turns
K1 0.4@2.5, 6 turns
#6 (permalink)      5/17/2017 9:24:30 PM US Central   quote/reply + tips
Peppesantander
Member
  • JoinedMay 2016
  • Posts 3
  • Reviews 0
  • Kudos2
🤔...il setup perfetto che consiglia il modder é 5 spire su punta da 2 di kantal 0.30...io uso 6 spire di 0.32 e una bomba 💣
#7 (permalink)      5/17/2017 9:43:34 PM US Central   quote/reply + tips
wuwei.ap
Member
  • JoinedMar 2015
  • Posts 22101
  • Reviews 266
  • Kudos42152
8 wraps on 2.5mm is good for 316L. I haven't received it, but that's where I will begin with 30 AWG. It's the same on my Kayfun Mini V2.1.
#8 (permalink)      9/5/2017 3:00:16 PM US Central   quote/reply + tips
pitus
Member
  • JoinedJan 2017
  • Posts 109
  • Reviews 5
  • Kudos22
I'm using 28Ga 5 or 6 wraps 2mm or 2,2mm. Around 1 ohm or 0,85 on mec mods it's amazing but only with booms, azhad and tobacs. No custards or fruity flavors.
#9 (permalink)      9/9/2018 3:00:31 AM US Central   quote/reply + tips
MC202_FT
Member
  • JoinedSep 2017
  • Posts 70
  • Reviews 4
  • Kudos20
The INOWIRE SS304 Hollow wire is fantastic on this atom: on these 18mm. atoms I use the 28ga It practically behaves as a 29ga, I found that inserting a fictious value of 0,27mm. wire diameter on Steam Engine works perfectly.

I usually make 8,5 wraps (many refers to it as 8 wraps) on a 2mm. I.D., ending up with a 0,90 Ohm coil, that has to be positioned slightly toward airhole side and levelled with the lower cup's lip or slightly (less than 1 mm.) higher.
Muji cotton, cut very short to just touch the bottom of the cup.

I vape it at 11,5-12,5W on a regulated mod, but it's almost perfect also on a mech or on a Pico Squeeze IF the battery isn't fully charged (at 4,0V it is a tad too hot of a vape for me, probably making 16-17W and 260-270 mW/mm² of heat flux).
On a mech I like it when the battery is around 3,7V-3,8V, an it allows for a wonderful vape for all the usable range down to 3,3V-3,2V lower limit.

Edited on 9/20/2018 at 5:56 PM. Reason: