coil build for 6 9 12mg nic creamy: FastTech Forums

Thread Tools Subscribe to this thread Working... Search within thread: Rate This Thread Login to rate this thread.
#1 (permalink) 3/6/2016 4:04:34 AM US Central quote/reply + tips
SinclairMart Verified JoinedDec 2015 Posts 12 Reviews 0 Kudos0	coil build for 6 9 12mg nic creamy I just ordered this 316L ss wire 26G.What coil should I make for my zephyrus v1 and v2.I vape on 60vg 40pg creamy juice at 6 9 12 mg.My device is a rx200 and vtc mini...any vwvv setting and tc settings? thanks. Working...
#2 (permalink) 3/6/2016 4:44:57 AM US Central quote/reply + tips
Migweld Verified JoinedOct 2014 Posts 1101 Reviews 0 Kudos475	I would do, 7 to 8 wraps, 3mm Inner diameter of coil, spaced coil for a 0.5 to 0.6 ohm coil TCR 108 for 316L ..best temp 200c to 220c or 390f to 430f SET power to 30 to 40 watts in VT is a good start point move up if you like... try this SKU 4089900 316L 28/32 clapton Edited on 3/6/2016 at 4:53 AM. Reason: Working...
#3 (permalink) 3/6/2016 4:50:50 AM US Central quote/reply + tips
SinclairMart Verified JoinedDec 2015 Posts 12 Reviews 0 Kudos0	Do you recommend doing micro coil on ss wire? Working...
#4 (permalink) 3/6/2016 4:51:37 AM US Central quote/reply + tips
johnny_469 Verified JoinedOct 2013 Posts 23118 Reviews 288 Kudos27287	Migweld wrote: I would do, 7 to 8 wraps, 3mm Inner diameter of coil, spaced coil for a 0.5 to 0.6 ohm coil TCR 108 for 316L ..best temp 200c to 220c or 390f to 430f SET power to 30 to 40 watts in VT is a good start point move up if you like... 3mm ID in a Zephyrus is huge IMO. Even with 26awg it will be a tight fit. 2.5mm ID is probably better in a zeph... These work really well in a Zephyrus, and are all 316SS in the middle, resistance section. Also, I think spaced coils perform better in a Zephyrus, but that's just from my experience. Edited on 3/6/2016 at 4:54 AM. Reason: Woah, mama! Working...
#5 (permalink) 3/6/2016 4:54:45 AM US Central quote/reply + tips
SinclairMart Verified JoinedDec 2015 Posts 12 Reviews 0 Kudos0	on the zeph v1 3mm is too big...the v2 is ok...but I usually do 2mm 8wraps 26G KA1.Im not sure about ss...because i heard that SS can be fired in vw and tc...not sure about a coil build for creamy flv with throat hit. Working...
#6 (permalink) 3/6/2016 4:59:10 AM US Central quote/reply + tips
Migweld Verified JoinedOct 2014 Posts 1101 Reviews 0 Kudos475	If you got the room try a coil spaced, not micro yes you can use watts or power mode.. just don't light up the coil before wicking red hot like kanthal, just add cotton and fill also a spaced coil will have less hot spots and you cant dry burn anyway to see, so go with spaced coil.. IMO Edited on 3/6/2016 at 5:03 AM. Reason: Working...
#7 (permalink) 3/6/2016 5:03:56 AM US Central quote/reply + tips
SinclairMart Verified JoinedDec 2015 Posts 12 Reviews 0 Kudos0	what will happen if i glow red ss... Working...
#8 (permalink) 3/6/2016 5:06:31 AM US Central quote/reply + tips
johnny_469 Verified JoinedOct 2013 Posts 23118 Reviews 288 Kudos27287	SinclairMart wrote: what will happen if i glow red ss... Red is fine, orange is pushing it (probably too far), and yellow is bad. Pulsing SS coils is more difficult than a-1 or nichrome wire because if it get's too hot, you'll "pop" (most likely melt) the wire. Edited on 3/6/2016 at 5:10 AM. Reason: Woah, mama! Working...
#9 (permalink) 3/6/2016 5:07:38 AM US Central quote/reply + tips
Migweld Verified JoinedOct 2014 Posts 1101 Reviews 0 Kudos475	It will oxidize the surface and melt the coating and wire will melt and its then not safe to vape like that after.. its not like kanthal a1 and yes pulse it is fine.. Edited on 3/6/2016 at 5:10 AM. Reason: Working...
#10 (permalink) 3/6/2016 5:18:13 AM US Central quote/reply + tips
SinclairMart Verified JoinedDec 2015 Posts 12 Reviews 0 Kudos0	so ss is something like titanium...cant be dry burn...how about the wire...is it springy... Working...
#11 (permalink) 3/6/2016 5:20:43 AM US Central quote/reply + tips
johnny_469 Verified JoinedOct 2013 Posts 23118 Reviews 288 Kudos27287	SS wire is easier to coil than a-1 or nichrome, imo. It's more stiff, but holds its shape better too. It's nowhere near as bad as Ti when it comes to the "no dry burning" rule. Edited on 3/6/2016 at 5:21 AM. Reason: Woah, mama! Working...