shopping cart empty
[dismiss] Kung Hei Fat Choy. FastTech will be on holiday from January 20, 2020, to January 31, 2020. Shipping and support will resume normal service on February 1, 2020. (details)
WORLDWIDE FREE SHIPPING

What batteries too use?
Login to post a new topic and to write a reply.
Thread Tools Rate This Thread


Search within thread:

Login to rate this thread.
#1 (permalink)      9/30/2013 10:03:53 PM US Central   quote/reply + tips
TraiLice
Member
  • JoinedDec 2012
  • Posts 261
  • Reviews 14
  • Kudos62
What batteries too use?
Ok you are really supposed to use IMR protected batteries with this right?
Fasttech does not have any though.
I want this but will not use my nitecore 14500's with it unless it is REALLY safe.
It is better to be silent and thought a fool, Than to speak up and remove all doubt.
#2 (permalink)      9/30/2013 10:27:06 PM US Central   quote/reply + tips
zombie55
Member
  • JoinedAug 2013
  • Posts 760
  • Reviews 689
  • Kudos600
+5 details
your best bet is aw 4.8 amp rating or efest 4.5 amp rating IMR so you can not really go sub ohm but 0.9 ohm - 1 ohm coil right on the limit

IMR battery's are not protected but they are safe chem these are the only 14500 batteries that you can vape with at around 1 ohm if you tried to use a protected battery the amp draw would be to much

the aw are c8
i think the efest is c8 but not sure

The C-Rating also indicates the amount of time the battery can support that discharge rate. A 1 C battery can support the calculated draw continuously for 1 hour. 2 C would be 1/2 of an hour. 10C would be 1/10 of an hour

voltage/ohms = amp

so 4.1v/ 0.95 ohm coil = 4.4 amp draw

if your a chain vaper then be careful cos you near the battery rated limit or increase the ohm's to lower the amp draw

i order this today i got a genesis ready to go 0.95 ohms

happy vape land

Edited on 9/30/2013 at 10:35 PM. Reason:
#3 (permalink)      10/1/2013 3:53:55 AM US Central   quote/reply + tips
armalitem16
Member
  • JoinedSep 2013
  • Posts 369
  • Reviews 0
  • Kudos166
+1 details
This little thang is sooooo tempting...
#4 (permalink)      11/11/2013 4:53:42 PM US Central   quote/reply + tips
eklikewhoa
Member
  • JoinedSep 2013
  • Posts 15
  • Reviews 42
  • Kudos2
anyone have flat top 14500 batteries? I think the flat top or shorter 14500 would help with the threading problem between the two tubes. I put Noalax on them and that helped a bit but didn't fix it completely.
#5 (permalink)      3/6/2014 1:29:25 PM US Central   quote/reply + tips
Shamus
Member
  • JoinedJun 2013
  • Posts 253
  • Reviews 97
  • Kudos73
Since it's telescopic, could you use 14650 batteries?
#6 (permalink)      3/18/2014 11:28:31 AM US Central   quote/reply + tips
Avatar
dcxx1981
Member
  • JoinedFeb 2014
  • Posts 953
  • Reviews 11
  • Kudos1020
+1 details
and remember ohms law, the actual voltage across the coil will be your starting point for making your calculations. for example my magneto gets .88 volt drop, so a fresh charged battery at 4.19 will be only 3.31(lots of drop thank you stupid damn spring loaded center pin).
so ohms law would be 3.31volts 3.48amps .95ohms 11.53 watts.
heres a link to ohms law calculater
http://www.ohmslawcalculator.com/ohms_law_calculator.php
THIS LINK IS A MUST FOR RBA!
by the way i modded the magneto to get a .2 voltage drop I'm so proud.
stations of the crass
#7 (permalink)      12/1/2014 4:50:15 AM US Central   quote/reply + tips
seadog
Member
  • JoinedOct 2013
  • Posts 17
  • Reviews 0
  • Kudos1
Efest

14500 700mah 8C 5.6amp

14650 950mah 10C 9.5amp

I use 14500 in a Lrider Mini Lambo & 14650 in a Trueman TF-1